USD
  • USD
  • EUR
  • GBP
0

Xenocron

Xenocron DIY Wheel Speed Sensor Kit (RWSS)

Xenocron Tuning's new WHEEL SPEED SENSOR Kit for Do-It-Yourselfers This kit allows you to easily ...

Xenocron Tuning's new WHEEL SPEED SENSOR Kit for Do-It-Yourselfers This kit allows you to easily add a Hall Effect sensor to your vehicle for monitoring wheel speed, shaft speed...etc, anything you can think of that can use it. Wire it in to an extra Wheel Speed Input on your Standalone Engine Management System or replace your Transmission mounts VSS (vehicle speed sensor) to use Rear Wheel speed (Ground Speed) versus Front Wheel Speed. Kit Includes: Magnetic Hall Effect Speed Sensor 10' Shi...

(8 variants)

PWM Boost ECU Components for OBD1 Hondata S300 ...

Add PWM Boost Control to your OBD1 Honda ECU using the factory EGR Circuit This kit will work for...

Add PWM Boost Control to your OBD1 Honda ECU using the factory EGR Circuit This kit will work for Hondata S300 or Neptune PWM boost control as well using the "EGR" Pin A11 setting. Add either our Xenocron 3 Port or 4 Port PWM Solenoid Kit to your order and use your Honda OBD1 ECU to control boost!

$10.00

Xenocron VTEC Conversion Parts Kit (OBD1 ECU)

OBD1 ECU VTEC Conversion Kit (Uberdata, Crome, Hondata & Neptune compatible) Convert your n...

OBD1 ECU VTEC Conversion Kit (Uberdata, Crome, Hondata & Neptune compatible) Convert your non-vtec ECU (PR4/P05/P06/P75) to a VTEC ECU Runs identical to any P28 VTEC ECU Notes: - Includes all components to convert your USDM OBD1 non-Vtec ECU to control Vtec (PR4/P05/P06/P75) - Please SPECIFY and know what board type you are converting - If you have a 1720 P05 ECU, the extra transistor for the O2 Sensor conversion from 1-wire to 4-wire will be included already - If you have any questions...

(3 variants)

Chipping Kit w/ SST Chip (OBD1 ECUs)

H O N D A / A C U R A OBD0 or OBD1 ECU Chipping Kit w/ SST Eprom (eCtune / Crome / Uberdata / N...

H O N D A / A C U R A OBD0 or OBD1 ECU Chipping Kit w/ SST Eprom (eCtune / Crome / Uberdata / Neptune / Hondata / TurboEdit / BRE) This is my standard ECU chipping kit that will come with everything you need to chip your own OBD0 or OBD1 Honda/Acura USDM ECU. Instructions are located in the 'Tech Center' section of the site. ***OUR KITS NO LONGER CONTAIN COMPONENTS C51 & C52, AS THEY ARE NOT REQUIRED*** USDM Kit Includes - 28 pin machined DIP Socket - 28 pin Aries ZIF Socket - 4 pin ...

(12 variants)

Chipped OBD1 VTEC ECU

***PLEASE READ ITEM DESCRIPTION BEFORE ORDERING*** Honda OBD1 VTEC ECU (P28 Equivalent for VTEC) ...

***PLEASE READ ITEM DESCRIPTION BEFORE ORDERING*** Honda OBD1 VTEC ECU (P28 Equivalent for VTEC) Socketed and ready to go for chip applications like Neptune, Crome, eCtune, Uberdata, or Hondata (S100/S200).  Also available for hardware systems like  Hondata S300 (prep for S300, no S300 included) or Neptune RTP (prep for RTP, no RTP included) All ECUs Professionally chipped and tested before being shipped Comes chipped with a ZIF socket, datalogging header and a custom basemap burned to a reb...

(14 variants)

Basemap Chip - Xenocron Custom

***PLEASE READ ITEM DESCRIPTION COMPLETELY BEFORE ORDERING***   Choose this product if you want a...

***PLEASE READ ITEM DESCRIPTION COMPLETELY BEFORE ORDERING***   Choose this product if you want a custom basemap created and burned to a chip using CROME PRO SOFTWARE only. Use this option if you ONLY want a basemap and chip and not necessarily the components used to chip your own ECU (see CHIPPING --> ECU KITS) When sending in your order, INCLUDE THESE DETAILS IN THE COMMENTS BOX as you checkout or your order will be delayed: - Engine (engine Code, Size, and specific internal work) - Inje...

(2 variants)

Xenocron Basemap File for S300, KPRO, or FlashPro

***PLEASE READ ITEM DESCRIPTION BEFORE ORDERING***   Choose this product if you want a basemap cr...

***PLEASE READ ITEM DESCRIPTION BEFORE ORDERING***   Choose this product if you want a basemap created with Hondata S300, Hondata KPRO, or Hondata FlashPro that is to be EMAILED to you ONLY. No extra chip will be supplied, included or mailed to you with the purchase of this item. This file will not be uploaded to a system purchased from us before shipping out. You will receive the email and must connect and upload the file on your end. Please see software help files for your specific software...

(3 variants)

Fuel Pressure Regulator Blank 06-15 Civic

Fuel Pressure Regulator Blank Used for Fuel Systems to retain stock feed design in-tank, elimina...

Fuel Pressure Regulator Blank Used for Fuel Systems to retain stock feed design in-tank, eliminating the possibility of rubber hoses bursting Fits: 2006-2015 Civic, Scion FRS and Subaru BRZ May also fit 04-14 TSX, 2013+ ILX, based on technical drawings. DOES NOT FOT RSX, EP3, EM2 CIVICS

$29.95

Xenocron EMAP Backpressure Kit

Xenocron Exhaust Manifold Back Pressure Kit This is a combination of products that will allow you...

Xenocron Exhaust Manifold Back Pressure Kit This is a combination of products that will allow you to add or log an Exhaust Manifold Pressure Readings through your ECU or datalogger This kit includes: (1) Backpressure Canister (Pressure Pulsation Damper) (1) Steel 1/8" NPT Weld Fitting (2) Compression Fittings (1 90 deg, 1 straight) 3 Feet of Flexible Copper Tubing Optional on this kit is an AEM 3.5 bar or 5.0 bar map sensor, or if you would like to use your own map sensor, you can choose th...

(3 variants)

Xenocron B-Series Complete Cam Degree Kit

Our Xenocron Cam Degree kit invented and designed by Mike Belben enable you to not only degree-in...

Our Xenocron Cam Degree kit invented and designed by Mike Belben enable you to not only degree-in your B-Series camshafts, but to check valve-to-valve and valve-to-piston clearances as well. No high-performance motor should be assembled without performing these procedures, and with this kit you can easily do them yourself. This COMPLETE KIT includes the following: (1) Dial indicator extension (1) Aluminum mount for outer dial indicators (B-Beam) (1) Aluminum mount for center dial indicator (...

$249.00

Tuning Deposit

This is our tuning deposit for a specific date in the schedule. All dates are first come first se...

This is our tuning deposit for a specific date in the schedule. All dates are first come first serve.   Balance due will be required when you arrive for your appointment. Please see our Dyno Tuning Agreement as a brief overview for how you should prepare for your tuning appointment. You will be sent a confirmation EMAIL once set in the schedule. This email will be for a specific date, time and will include our tuning agreement with your responsibilities that must be completed before arriving ...

(4 variants)

Xenocron Q31 Transistor

Transistor for Honda ECU spots labeled Q34 or Q31 Q31 is the transistor that commonly blows up wh...

Transistor for Honda ECU spots labeled Q34 or Q31 Q31 is the transistor that commonly blows up when someone plugs the Purge Control Solenoid plug into the IAT sensor.

$2.00

Xenocron Motorola 2.5 Bar MAP Sensor Kit

The kit includes one Motorola 2.5 Bar Map sensor,detachable connector and 12" of colored wire wit...

The kit includes one Motorola 2.5 Bar Map sensor,detachable connector and 12" of colored wire with online instructions to hook it into your stock MAP wiring. Upgrading from a stock Honda/Acura Map sensor that can only read ~10 psi of boost will allow you to run up to ~21.75 psi of boost as well as set a boost cut in your engine management. This safety feature has saved many motors from overboosting due to many random factors/problems that occur on Turbo Charged vehicles. This sensor is extrem...

$40.00

Hondata S300 Chipping Kit

This is a chipping kit designed for Hondata S300 Boards Only Includes - 32 pin machined header - ...

This is a chipping kit designed for Hondata S300 Boards Only Includes - 32 pin machined header - 0.1µf ceramic disc capacitors (qty 2) - 1k resistor - 74 HC373 chip NO JDM OPTION

$15.00

RDX 410cc Injectors - Set of 4

Genuine US Spec RDX Injectors now available and in stock! This is a Set of (4) RDX 410cc OEM Inj...

Genuine US Spec RDX Injectors now available and in stock! This is a Set of (4) RDX 410cc OEM Injectors. No clips, adapters, spacers, etc are included in this kit, it is JUST injectors. We do keep these in stock, so if you see this item, know that it will ship out right away. As an added bonus, we sent a set of these out to be dynamically tested by Injector Dynamics and we include a real average dead-time chart with every set purchased through Xenocron. See other products in this category for...

$240.00

Xenocron IAT Relocation Flange

This is an aluminum flange, CNC Machined to allow you to relocated for factory Honda/Acura IAT (i...

This is an aluminum flange, CNC Machined to allow you to relocated for factory Honda/Acura IAT (intake air temperature) sensor to a charge pipe or intake. In the factory configuration, it is a known fact that aluminum intake manifolds can become heat soaked, which falsely gives the ECU a higher air temp reading. In a stock motor/ecu setup this isn't a problem, however when you add a turbocharge, supercharger, or other aftermarket bolt-ons, this can cause issues. Ideal placement of the IAT sen...

(2 variants)