USD
  • USD
  • EUR
  • GBP
0

Xenocron

Xenocron DIY Wheel Speed Sensor Kit (RWSS)

Xenocron Tuning's new WHEEL SPEED SENSOR Kit for Do-It-Yourselfers This kit allows you to easily ...

Xenocron Tuning's new WHEEL SPEED SENSOR Kit for Do-It-Yourselfers This kit allows you to easily add a Hall Effect sensor to your vehicle for monitoring wheel speed, shaft speed...etc, anything you can think of that can use it. Wire it in to an extra Wheel Speed Input on your Standalone Engine Management System or replace your Transmission mounts VSS (vehicle speed sensor) to use Rear Wheel speed (Ground Speed) versus Front Wheel Speed. Kit Includes: Magnetic Hall Effect Speed Sensor 10' Shi...

(8 variants)

PWM Boost ECU Components for OBD1 Hondata S300 ...

Add PWM Boost Control to your OBD1 Honda ECU using the factory EGR Circuit This kit will work for...

Add PWM Boost Control to your OBD1 Honda ECU using the factory EGR Circuit This kit will work for Hondata S300 or Neptune PWM boost control as well using the "EGR" Pin A11 setting. Add either our Xenocron 3 Port or 4 Port PWM Solenoid Kit to your order and use your Honda OBD1 ECU to control boost!

$10.00

Xenocron IAT Relocation Flange

This is an aluminum flange, CNC Machined to allow you to relocated for factory Honda/Acura IAT (i...

This is an aluminum flange, CNC Machined to allow you to relocated for factory Honda/Acura IAT (intake air temperature) sensor to a charge pipe or intake. In the factory configuration, it is a known fact that aluminum intake manifolds can become heat soaked, which falsely gives the ECU a higher air temp reading. In a stock motor/ecu setup this isn't a problem, however when you add a turbocharge, supercharger, or other aftermarket bolt-ons, this can cause issues. Ideal placement of the IAT sen...

(2 variants)

Xenocron Motorola 2.5 Bar MAP Sensor Kit

The kit includes one Motorola 2.5 Bar Map sensor,detachable connector and 12" of colored wire wit...

The kit includes one Motorola 2.5 Bar Map sensor,detachable connector and 12" of colored wire with online instructions to hook it into your stock MAP wiring. Upgrading from a stock Honda/Acura Map sensor that can only read ~10 psi of boost will allow you to run up to ~21.75 psi of boost as well as set a boost cut in your engine management. This safety feature has saved many motors from overboosting due to many random factors/problems that occur on Turbo Charged vehicles. This sensor is extrem...

$40.00

ECU Chipping Service

This is a service for sending in your stock OBD1 ECU for chipping. Once placed, we will hold onto...

This is a service for sending in your stock OBD1 ECU for chipping. Once placed, we will hold onto your order until your ECU arrives and match it up so please put a copy of your order inside the box with the ECU when you send it in to us. Includes: All chipping parts, ZIF socket and (1) reburnable eprom Labor for installing components and testing of your completed ECU on the bench.  We test every ECU before it leaves for function (we do not test them before we chip them, we assume all are 100...

$69.95

E-Tuning Service

E-Tuning by Xenocron "E-Tuning" or EMail Tuning Service provided by Xenocron will be for a select...

E-Tuning by Xenocron "E-Tuning" or EMail Tuning Service provided by Xenocron will be for a select set of engine management systems listed below. This list will grow as we add more systems. Our E-Tuning service will focus on SAFETY and DRIVEABILITY using logs you will send us taken by the engine management system you are using. Once you purchase our service we will be partners in making sure your vehicle, runs, drives and is safe! As we always promote, for the ultimate in PERFORMANCE and RELIA...

$299.00

Xenocron D.I.Y RWSS SENSOR ONLY

This is the Sensor ONLY to our very popular Rear Wheel Speed Sensor kits. This is to be used for ...

This is the Sensor ONLY to our very popular Rear Wheel Speed Sensor kits. This is to be used for the replacement of the original sensor.

$59.95

Flex Fuel Converter Kit

A little Flex Fuel kit we worked up for those of you needing a tidy solution where your ECU accep...

A little Flex Fuel kit we worked up for those of you needing a tidy solution where your ECU accepts a 0-5 volt signal for flex % content! Kit Includes: Flex Fuel Sensor Flex Fuel Converter Wire Harness Connectors

$249.00

Xenocron K-series ECU pin 10-pack

This is a pack of 10 small ecu pins for K-series Honda/Acura ECUs. Use these for wiring in additi...

This is a pack of 10 small ecu pins for K-series Honda/Acura ECUs. Use these for wiring in additional inputs/outputs, replacing broken pins, etc. Feel free to call or email with any questions you may have.

$10.00

Xenocron 3 Bar MAP Sensor Kit (GM)

Comes with new 3 bar map sensor, weatherpack pigtail connection with pins and directions for the ...

Comes with new 3 bar map sensor, weatherpack pigtail connection with pins and directions for the most common Honda wiring. This sensor allows you to run up to approximately ~29 psi of boost on Speed Density based engine management systems. The calibration of this map sensor is the same as a factory GM 3 Bar Sensor

$65.00

HC373 Thru-Hole Latch

20 Pin Thru Hole Latch for OBD1 Honda ECUs

20 Pin Thru Hole Latch for OBD1 Honda ECUs

(2 variants)

Flex Fuel Sensor

Flex Fuel Sensor's are in stock! The Flex Fuel Sensor detects the ethanol concentration in a gaso...

Flex Fuel Sensor's are in stock! The Flex Fuel Sensor detects the ethanol concentration in a gasoline / ethanol fuel mixture and provides alcohol content pre-injection. The engine controller utilizes sensor output to control the stoichiometric air-to-fuel ratio. In cold start combustion it improves efficiency and pollutant emissions following a refueling event. Picture shows actual product!

$65.00

Xenocron K Series - DIY Xenocron Map Sensor Kit

This is our BRAND NEW DIY Stock Map Sensor Housing kit for the K Series tuning enthusiast. The pa...

This is our BRAND NEW DIY Stock Map Sensor Housing kit for the K Series tuning enthusiast. The package includes the following pieces: K Series Map Sensor casing (top/bottom) Your choice of Motorola 2.5 or 4.0 bar Map Sensor Circuit Board for the pressure sensor Small 18g wire (red, black & green) Special High Quality Glue for securing the two halves Instructions This unit when assembled will fit the stock map sensor location on the K Series and plug into the factory wiring. Will work wi...

(2 variants)

HC373 Surface Mount Latch

20 Pin Surface Mount Latch for JDM OBD1 ECUs

20 Pin Surface Mount Latch for JDM OBD1 ECUs

$3.00

Xenocron DIY OBD2 Honda - RDX Adapter

This is a DIY product! This item is listed PER INJECTOR, order the quantity based on how many inj...

This is a DIY product! This item is listed PER INJECTOR, order the quantity based on how many injectors you need to adapt! Included is: ONE set of pins, grommets and clip for RDX Injector ONE set of pins, grommets and clip for OBD2 Male Enough wire to complete the kit If you have questions, please email us PRIOR to ordering. There will be no returns or exchanges on these items.  

$9.99

Xenocron DIY OBD1 Honda - RDX Adapter

This is a DIY product! This item is listed PER INJECTOR, order the quantity based on how many inj...

This is a DIY product! This item is listed PER INJECTOR, order the quantity based on how many injectors you need to adapt! Included is: ONE set of pins, grommets and clip for RDX Injector ONE set of pins, grommets and clip for OBD2 Male Enough wire to complete the kit If you have questions, please email us PRIOR to ordering. There will be no returns or exchanges on these items.  

$8.99