USD
  • USD
  • EUR
  • GBP
0

Sales and Specials

AEM V2 Water/Methanol Injection Kit, Standard C...

***This item is typically ordered as needed, please contact us to check availability before placi...

***This item is typically ordered as needed, please contact us to check availability before placing your order*** Part Number: 30-3300 - V2 Water/Methanol Injection Kit, Standard Controller - Internal MAP with 35psi max, 200psi WM Pump, 1 Gallon Reservoir, Conductive Fluid Level Sensor THE AEM WATER/METHANOL INJECTION SYSTEM ADVANTAGE Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet ...

$467.03 $609.09

The Stay Cool, Dont Over Heat Package

Here at Xenocron we know how hot it can get out there for us, and even more so for our CARS! It's...

Here at Xenocron we know how hot it can get out there for us, and even more so for our CARS! It's about time you did something for that old work horse or that not so stock "Daily Driver". We are proud to offer you these quality products at the lowest package price possible. This package includes: Koyo Honda/Acura Dual core Half Rad with Koyo RAD CAP Maradyne 11" Slim Fan Motul MoCool Coolant Additive ITS LIKE GETTING THE MOCOOL AND THE SLIM FAN FOR FREE! IF YOU HAVE ANY QUESTION P...

$325.00 $401.90

Russell -6AN Male to -8AN Male O-Ring Radius Po...

Russell#799-670640 AN O-Ring Radius Port Fitting -06 AN Male -08 AN O-Ring Port Black Anodized Fi...

Russell#799-670640 AN O-Ring Radius Port Fitting -06 AN Male -08 AN O-Ring Port Black Anodized Finish 1/pkg.

$9.64 $10.71

Xenocron Billet M.A.P Adapter

Here we have a billet M.A.P sensor adapter. It mounts to the Factory map sensor location on most ...

Here we have a billet M.A.P sensor adapter. It mounts to the Factory map sensor location on most B,D,H,F throttle bodies to allow you to run a line to a remote/ or firewall mounted map sensor. Is threaded to except 1/8 npt fittings.

$20.00 $25.00

Xenocron EMAP Backpressure Damper

This is a Exhaust Manifold Backpressure damper that aids in the ability to measure backpressure o...

This is a Exhaust Manifold Backpressure damper that aids in the ability to measure backpressure on your turbocharged vehicle. This item is for the damper only but to completely install this you might require fittings, line, and a sensor. ***IF YOU HAVE ANY QUESTIONS PLEASE CALL OR EMAIL BEFORE PLACING YOUR ORDER***

$69.95 $79.95

Skunk2 70mm Alpha Series Throttle Bodies for B/...

Skunk2’s Alpha Series Throttle Bodies are designed to be used with factory intake manifolds as ...

Skunk2’s Alpha Series Throttle Bodies are designed to be used with factory intake manifolds as well as Skunk2’s Pro Series Intake Manifolds for bolt-on horsepower and torque gains by optimizing engine airflow, all at a competitive price. Skunk2’s Alpha Series Throttle Bodies are precision die-cast from high-quality materials and include features found in our Pro Series line, like countersunk mounting bolts, solid brass throttle plates, and idle adjustment screws for fine tuning. Each Al...

(2 variants)

K-Tuned Shifter Cable Trans Bracket

Application: RSX (All Models and Years), EP3 Civic, 2006-2011 Civic SI (K20Z3) with 2002-2006 RSX...

Application: RSX (All Models and Years), EP3 Civic, 2006-2011 Civic SI (K20Z3) with 2002-2006 RSX-S Shift Selector We have had the idea to make a nice replacement Shifter Cable Bracket for quite some time now. While we were developing our Billet RSX Shifter and our Race Shifter Cables, it made sense for us to work on a cable bracket at the same time. After testing a few prototypes of different materials, we couldn’t get the bracket to look the way we wanted. In the end, we decided to get it m...

$71.99 $79.99

K-Tuned Heater Hose Delete Cap

These simple caps are used to block off any unused 5/8î diameter coolant ports. They come in hand...

These simple caps are used to block off any unused 5/8î diameter coolant ports. They come in handy when deleting heater hoses and other coolant related accessories. Engine setups using our K-Tuned Water Plate system will find these bypass caps very useful. Sold individually.

$7.19 $7.99

DIY - Swapbox K-Series Immobilizer Disable

This is the "Swapbox" K-Series Immobilizer Delete box designed for use when swapping a stock K-Se...

This is the "Swapbox" K-Series Immobilizer Delete box designed for use when swapping a stock K-Series motor into your vehicle. The unit has immo-bypass AND multiplexer error removed so it should run like a stock vehicle for you. The connections are easy and simple and instructions are included with the unit. These items are IN STOCK and shipping immediately! Please call with any questions! Swapbox-K comes with: Mobilizer Module, two splice terminals and two precrimped Contacts for the connect...

(5 variants)

K-Tuned K Series Swap Traction Bar

Please Note.. Picture is of the K-Series Swap Traction Bar for 88-91 Civic / CRX Set-Up. - Gen 3...

Please Note.. Picture is of the K-Series Swap Traction Bar for 88-91 Civic / CRX Set-Up. - Gen 3 Bars, fully new design to completely eliminate and failures - Aluminum Swaged radius arms (stronger and better) - Tig and Mig welded for the best strength - New double rod end (heim joints) on each end of the radius arm - Control arm mounting tabs - Full mounting hardware package included - Gen 3 bars are stronger all around - New ultra tough powder coating, the strongest and thickest ever - New ...

(3 variants)

K-Tuned Coolant Temp Sensor Adaptor Fitting (fo...

Unlike other fittings on the market, this fitting is designed to fit perfectly on your K-Series e...

Unlike other fittings on the market, this fitting is designed to fit perfectly on your K-Series engine. The fitting is designed to replace the oem Idle Air Assist Valve and give you the perfect location for the coolant gauge temp sensor. This sensor must be added to allow a K-swap vehicles cluster to accurately read the coolant temp.

$10.79 $11.99

Rywire K-Series Swap Harnesses

Rywire K-Series Chassis Adapter This adapter is made to allow the installation of a K-Series engi...

Rywire K-Series Chassis Adapter This adapter is made to allow the installation of a K-Series engine with the 02-04 K20 engine harness. It will also work for our all RYWIRE K-Series engine harnesses. K1 & K2 types! This wire harness connects your K-Series engine harness to your chassis interior harness while adding the E-plug and all its functions. This harness is primarily made for a K-Pro or Re-Flashed ECU but can be used with a stock RSX ECU provided you have bypassed the immobilizers a...

(10 variants)

K-Tuned Universal A/C & P/S Eliminator Kit

Fits all K20/24 engines Eliminates P/S and A/C. CNC machined 6061 billet aluminum. Clear anodize...

Fits all K20/24 engines Eliminates P/S and A/C. CNC machined 6061 billet aluminum. Clear anodized for durability. Pulley is hard anodized. NTN bearing (identical to oem Honda bearing) Tension is fully adjustable. Includes all hardware. Allows proper clearance for the EF chassis. The billet alternator pulley now comes with all K-Tuned Pulley kits You no longer need to buy the EP3 idler pulley setup from Honda to complete a K-series engine swap in your car. The K-Tuned pulley kit eliminates b...

$197.99 $219.99

K-Tuned K20/24 Universal Swivel Neck Thermostat...

K-Tuned has the solution to your lower rad hose problems. Some of the motors we have received cam...

K-Tuned has the solution to your lower rad hose problems. Some of the motors we have received came with an OEM plastic water neck broken. Until now, you could only order a replacement part from Honda/Acura. Problem is they only sell the housing complete with the thermostat, which is pretty expensive and it doesn’t provide any real benefits. If your housing isn’t broken then you still have to get the right hose, with the right angles and mate it to the radiator. After that, you have to fig...

$152.99 $169.99

Mr. Gasket -8AN Stainless Steel Braided Hose

Mr. Gasket Stainless Steel Braided Hose uses a rubber tube on the inside and a stainless steel br...

Mr. Gasket Stainless Steel Braided Hose uses a rubber tube on the inside and a stainless steel braid for strength, and is compatible with most fuels, coolants, and oils. With a temperature range of -40 to 300 degrees F, and a maximum pressure rating of up to 1,000 psi, it can handle nearly any plumbing job safely and securely. Length: 4ft

$13.00 $29.25

Mr. Gasket -8AN 150 Degree Swivel Fitting

When you need maximum performance and durability look to these high quality fittings from Mr. Gas...

When you need maximum performance and durability look to these high quality fittings from Mr. Gasket. Each fitting is constructed from aluminum and given a unique black and silver finish. They are good up to 1000 psi and are resistant to most all automotive chemicals. -8 AN, 150 degree.

$19.00 $34.50