USD
  • USD
  • EUR
  • GBP
0

Moates

BURN2 USB Chip Burner

The Burn2 has all the functionality of the Burn1 but is smaller and uses a mini-USB cable. The ne...

The Burn2 has all the functionality of the Burn1 but is smaller and uses a mini-USB cable. The new "heartbeat" LED light lets you know whether a chip is in the burner and if it is positioned in the correct direction. Most commonly used with Crome, Crome PRO, eCtune, Neptune, Hondata, TurboEdit, BRE (Ben Ogle\'s ROM Editor), Uberdata, & Tuner PRO USB Chip Programmer works with the AT29C256, 27SF512, and AM29F040 chips. Self-powered from the USB port, so no power adapter is needed! Burner c...

(3 variants)

Moates HULOG Honda USB Datalog Interface

With this device (an encased version of the Hondalog), you can perform datalogging on your Honda...

With this device (an encased version of the Hondalog), you can perform datalogging on your Honda ECU using USB as your PC interface. Comes with converter box, USB cable, and a cable to go from the box to your 4-pin header on the ECU. Datalogging Description

$35.00

Neptune/Demon Bluetooth Module Add-on

This Bluetooth module has been thoroughly tested and pre-configured for direct plug-n-play use ...

This Bluetooth module has been thoroughly tested and pre-configured for direct plug-n-play use with the new Neptune/Demon2 package combo! Compatible with the Android TunerView application as well as PC-based Neptune tuning and logging communications. Includes labeled 12" 4-pin attachment cable and shrink-protected ECU/Demon-side Bluetooth dongle. Also compatible with other devices by simply re-pinning the cable end, but comes ready to roll for Neptune/Demon2 RTP. FOR USE WITH THE NEW ...

(2 variants)

Moates Ostrich Emulator Ribbon Cable

EMUC2818 Emulation Cable 28-pin 18-inch Same as cable length for emulation products, works as a s...

EMUC2818 Emulation Cable 28-pin 18-inch Same as cable length for emulation products, works as a spare or replacement.

$10.00

Demon 2 eProm Emulator and Datalogging Hardware

NEW AND IMPROVED IN STOCK AND READY TO SHIP! The Demon 2 is the newest in our line of Honda/Acura...

NEW AND IMPROVED IN STOCK AND READY TO SHIP! The Demon 2 is the newest in our line of Honda/Acura-friendly P28/P30/P72-compatible technology. Totally bumpless realtime emulation (real time tuning), embedded datalogging, auxiliary ports, 16x calibration storage. In-situ device, Demon 2 fits inside both USDM and the Demon 1in the JDM ECUs. Gives all the power of the Ostrich, Hulog, RTP, and other products into one. Full native compatibility with Crome, Neptune, TunerPro, and others. The Moates ...

(12 variants)

Moates Replacement Battery Ostrich 2.0

You should never need a battery replacement on the Quarterhorse, Ostrich2, or Roadrunner, but if ...

You should never need a battery replacement on the Quarterhorse, Ostrich2, or Roadrunner, but if you do (if you short the old one out or something), then you can use this. Most units are soldered in, so be prepared to desolder the old one to replace it. If the old one measures over 2 volts then it should be fine so don't replace it!

$5.00

Moates Ostrich 2.0 USB Real Time ECM Emulator

The newest breed of emulator has evolved! Ostrich Emulator Description This is the newest Ostrich...

The newest breed of emulator has evolved! Ostrich Emulator Description This is the newest Ostrich, the 2.0 unit. It is extremely small and compact, durable, versatile, and powerful. Full 921.6k speed, from 4k (2732A) up to 512k (4mbit 29F040) and everything in between (27C128, 27C256, 27C512). Also works in conjunction with the FordEmu interface. This new design distills the experience to date from the Ostrich product, adding key power features such as address tracing, totally bumpless upload...

(2 variants)

Moates Demon ECU Pins

These are the pins that are specifically for use when installing a Moates Demon. These are the sa...

These are the pins that are specifically for use when installing a Moates Demon. These are the same pins that are included in the kit that comes with the Demon. If for some reason you lost or broke yours, these will work as a replacement. This item includes 28 pins, enough for one Demon installation.

$10.00

4 Wire Hulog Cable

This is a replacement 4 wire cable for the Moates Hulog.

This is a replacement 4 wire cable for the Moates Hulog.

$5.00

Moates Nissan 2-Chip Adapter

This adapter allows you to connect to a 2x20 IDC pin header in a Nissan ECU. It accepts two 27SF...

This adapter allows you to connect to a 2x20 IDC pin header in a Nissan ECU. It accepts two 27SF512 chips (available separately). Can also be used with two Ostriches for realtime capability. With this adapter, you program both chips with the same full code, no odd/even splitting needed. At this point, there are only one version of the boards, 1.1nm Applications: These boards are designed for S13 and B13 applications. They will NOT work with S14a ECUs that have a 20x2 pin header. They will n...

$50.00

Moates 2 Timer

This little gem plugs into your 28-pin socket that normally takes a 27C128 or 27C256. It has a si...

This little gem plugs into your 28-pin socket that normally takes a 27C128 or 27C256. It has a single wire lead coming off of it. Put a 27SF512 chip in it, and switch the wire lead to chassis ground to switch between two separate programs! Comes with a 27SF512 chip. Instructions are in the TECH CENTER

$30.00

Moates USB APU1 AutoProm Package

The APU1 is an all-in-one device aimed at the OBD1 GM platform. It burns and reads chips, does AL...

The APU1 is an all-in-one device aimed at the OBD1 GM platform. It burns and reads chips, does ALDL datalogging and realtime chip emulation in one USB device that does not require an external power supply! Specifically, it programs AT29C256, 27SF512 chips and reads 27C32, 27C128, 27C256, 27C512 chips. Performs ALDL communications at 160 and 8192 baud. Has 3-channel 0-5v 10-bit A/D provision for wideband and other datalogging. Package includes AutoProm device, 28-pin 18-inch emulation cable, O...

$325.00

Tunerview Demon Interface Module

This module is necessary if you want to use your Tunerview 2 with a Demon Board and originally or...

This module is necessary if you want to use your Tunerview 2 with a Demon Board and originally ordered it for another application. Note: An additional 4-pin header must be installed onto your Demon board for this module to function. Not needed with RD-1 display.

(3 variants)

Moates Socket Booster 1.0

The Socket Booster improves the signal conditioning at your chip or emulation socket. This is an ...

The Socket Booster improves the signal conditioning at your chip or emulation socket. This is an active circuit which boosts the address and data information to and from your target ECU. This is a great fix for that flickering SES light on the old GM TBI setups (747, etc). Drives the information more cleanly across the ribbon cable, allowing longer cable runs (3+ feet). Facilitates both remote emulation (when used with Ostrich 2.0) or remote-mount chip installation (when used with EMUC-series...

$40.00

SideSaddle

Used to mount the Quarterhorse (or other J3 device) externally instead of inside the ECU. Useful ...

Used to mount the Quarterhorse (or other J3 device) externally instead of inside the ECU. Useful for shops or tuners to avoid clearancing issues inside the ECU. NOT for permanent install, just a matter of convenience if using the QH for temporary sessions.

$10.00

S2 Aries 28-pin ZIF Socket

Very durable 28-pin ZIF socket. With this socket installed, you'll be able to switch chips in and...

Very durable 28-pin ZIF socket. With this socket installed, you'll be able to switch chips in and out of your G1 adapter or other application very quickly and easily! Heavy-duty construction, very good contact with pins. Great for emulation interfacing! For use with 29C256/27C128/27C256/27SF512/27C512 type systems. Package GP1 comes with this socket already. Goes well with a G2 adapter as well. This socket will not clearance some of the Honda ECUs, so we recommend the low profile S4 for those...

$10.00