Available NOW!

If you already have a Moates Ostrich Emulator, all you need is this license and a datalogging cable to begin tuning with eCtune which has become the newest premier OBD1 Tuning Editor on the block.

If you have previously purchased a Crome PRO software license from me in the past, contact me BEFORE buying this license to learn how you can save money. You must have purchased Crome PRO from me though...please keep this in consideration.

You MUST have an Ostrich Emulator to be able to use eCtune PRO and the Emulator must be permanently installed on the car using it. There is NO CHIP BURNING with this software.

Details on eCtune:

• High and low cam tables with size 24x20
• High and low load vtec window(tps based)
• Secondary maps(second set of high / low cam maps)
• Electronic boost controller(gear or rpm dependent)
  • RPM based compensation
  • IAT based compensation
  • Delta Map compensation(testing)
  • Closeloop(testing)
  • FastSpool option
  • Adjustable Outputs(EGR/IAB/Purge(testing)/ACC(testing))
  • Adjustable Hz
• Manual dual/tri/quad stage boost controller
• Cold, hot and MIL Stage boost cut protection
• 3-Step launch control with anti-lag and tps activation
• FTL Type
  • TPS activation
  • Fixed point
  • FTL memory set by a button(rev to rpm press button, rev in memory until reset)/testing
• FTS Type:
  • Fixed
  • Per Gear(testing)
• BurnOut:
  • Press a button/switch to activate the burnout rev limit(testing)
• Rev Limiter with fuel cut/ ignition cut/ fuel and ignition cut :
  • Hot and cold Rev
  • Hot can use per gear limiter(if you want a lower rev limit in first gear) (testing)
  • Soft Rev Limiter(Design phase)
• Gear depended shift light(MIL/check engine)
• 3 General purpose outputs with fuel/ignition adjustments(or ability to switch to secondary maps)
• Injector calibration with fuel offset, overall fuel trim and battery compensation table
• Fuel trims: injector, overall, o2, tps tip-in, crank, postfuel, iat.
• Gear based ignition and fuel corrections
• Target idle with IACV adjuster
• Closeloop(with use of wideband 0-5v signal)
  • Target O2 maps in sofware for each fuel map
  • Target O2 map in ecu(testing)
• Support of different kinds of mapsensors
• Table load selectable: map sensor/ tps sensor/ alpha-n
• Selectable gearbox
• User adjustable fuel cut settings
• Use any input for Service Check Connector or use KOEO TPS(key on engine off & tps>50%)
• Ac cut and ac idle recovery
• Disable Ignition correction above X mBar
• Starter signal disable
• Fuel pump control(disable/outputs/prime time)
• Alternator disable
• Control radiator fan with any output
• Ect overheat protection; limits rpm and throws code 6
  

• Datalogging:
  • Fast datalogging of 80 parameters
  • Live Tuner graphs( time vs AFR, rpm vs AFR/Boost)
  • Save logs for later analyzing, view in Grap mode
  • Export to CSV
  • Custom Data display
  • Warning range for most parameters
  • Graph templates for different type analyzing
  • Auto reconnect(search for ecu) on timeout
  • Datalog files with Marker including comments. Usefull for later reply.
    
• Realtime Updating
  • Fast updating of the rom
  • Upload a calibration only(less then 1 seconds)
  • Upload the base code(less then 4 seconds)
• Easy to use interface
  • Lots of options and data still organized
• Basemap creator
  • Selectable Ecu's
  • Selectable Basemaps for different engines
  • Adjust mapsensor during creation
  • Adjust injectors during creation
  • Select amount of columns, boost fuel, boost retard
• View and clear error codes
• Automatic software updates
• Table editing
  • Easy table editing
  • Auto Adjust selection based on wideband reading and target afr
  • Interpolate Row and Columns
  • Smooth Map or Smooth Selection
• Table Graphs
  • 2d presentation of data
  • 3d presentation of data
  • Advance visual editing of tables
• Map trails feature; You can see where the ecu read during a run, combined with rpm vs Afr/Boost you have powerful tool(see help file)
• Tuner Graphs(Live plots)
  • live Time vs AFR
  • live rpm vs Afr/Boost
  • rpm vs Accel(in development)
• Read or write chips
• eCtune uses universal calibrations which are rombase version independent
• Snapshot manager
  • Make snapshots during tuning. Roll back an old calibration fast.
• Export/Import tables only
• 3 user configurable analog inputs
• 3 inputs for wideband logging
• Different predefined widebands or use custom volt to afr table
• Tools for Injector Calibration, Tps Calibration, Timing Sync, Boost Tables and Killing Injectors
• Auto detects all hardware connected. Never again you need to know what comm port is what